Are you running out of battery and don’t know how to start your car? No panic! By itself, using jumper cables to charge the battery is not complicated! By following our tips and tricks, you will be able to start your car in no time. And above all, safely! So are you ready to learn how to jump start your car with jumper cables? He went away !
Starting a car with jumper cables is a simple matter if you do it right! We explain how to proceed. You will be able to connect your jumper cables correctly! Follow our advice, starting your vehicle will be child’s play!
Carrying all the jumper cables and knowing how to use them goes a long way. The key is to jump start your own vehicle in an emergency or help a motorist who has broken down.
Also read: Has anyone connected to my WiFi? How to find and avoid it
Car stopped on the side of the road. source: spm
One thing is for sure! Doing it correctly allows you to do it safely. Attention ! You could seriously injure yourself trying to start another vehicle. Please be careful to follow all instructions! Before connecting the jumper cables, refer to this safety checklist:
- First, make sure both batteries have the same voltage (most are 12 volts) and the same polarity (both batteries should have a negative ground). If necessary, do not hesitate to take a look at your user manual!
- Move the two vehicles closer to connect the cables. However, the two cars must not be close together (absence of contact) to avoid any risk of electrical short circuit.
- Before attempting to start, turn off the car’s engine. Also turn off the ignition, lights and other accessories. Finally, make sure that both parking brakes are firmly applied. Remember to wear protective glasses!
- No Smoking ! Sparks near a battery can cause an explosion hazard.
- If the weak battery is frozen, do not try to turn it on under any circumstances. To find out, look at the inspection plug to see if the water is frozen. Usually one or more sides of the battery stick out.
- Identify the positive and negative terminals of your battery. The positive terminal, probably connected to the car’s starter system, has a red wire with a + sign. The negative terminal, which is connected to the motor, has a – sign.
And there you have it! Now that everything is clear, let’s get to work!
When your battery is flat, jumper cables will make your life easier! However, you have to know how to use it. Follow our guide to use them correctly without any risk. How to use !
Connect the jumper cables to start the car. source: spm
- Connect the positive cable, red or yellow, to the positive terminal of your discharged battery. Attention ! The other end should not touch any part of the engine or the body of your car.
- Connect the other end of the positive cable to the positive terminal of the fully charged battery.
- Connect the negative black cable to the negative pole of the correct battery.
- Connect the other end of the negative cable to a clean bolt head or mount it to your car’s engine that has a low battery. Keep the clamp away from the battery, moving parts and the fuel system. ATTENTION ! Do not connect the negative cable to the negative terminal of the weak battery during the process. Common mistake! This could ignite the hydrogen gas above the battery, which could cause an explosion. Instead, connect it to a metal part of the engine. Battery explosions cause severe effects and injuries!
- Start the car with the correct battery. Let the low battery charge for 5 minutes and then try to start. If the car with low battery does not start, turn off both car engines, check the cables are tight and in good contact, then try a second time.
- When the car starts, please wait 15 seconds before unplugging the cables to avoid stalling.
And that’s it, that’s it! He has successfully jump started his car with simple jumper cables.
To disconnect your cables, you must do it in the reverse order. It is easy !
Also read: What you need to put in your wallet to attract prosperity in 2023. So you will have a prosperous year
- Remove the negative cable from the repaired car, and then the negative cable from the vehicle with the good battery.
- Then remove the positive cable from the car with the good battery. Do not touch a grounded part of either car with the positive cable clamp.
- Remove the positive cable from the car you repaired.
Why won’t my car start even after using the pliers?
Does your car not start even after using jumper cables? Turn off your engine, check if the connections between the wires and the terminals are made correctly, and restore the running order of your vehicle. If your vehicle does not start after several attempts, it means you need to replace your battery. Do not hesitate to go to a professional to give you an exact opinion, it could be other problems (bad start, etc.).
Our tips will be helpful in starting your car with jumper cables. Follow our tips to do it correctly and safely! If necessary, it’s time to test them. Up to you !
Also read: Do you dispose of plastic bottles in this way? you make a mistake
